Home > Products > Generators > Generac Standby Generator from QNP

Generac Standby Generator from QNP

Basic Info

BrandQNP

Generator TypeAlternator

Output TypeAC Three Phase

CertificationISO

StandardStandard

Additional Info

PackagingIn cases

TransportationOcean,Land

Place of OriginChina

CertificateISO9001,CE

PortQingdao Port,Shanghai Port

IncotermFOB

Product Description

Generac Standby Generator from QNP:

A Steam Turbine Generator is a device that uses steam to rotate a turbine generator to produce electricity.steam turbines use water that is heated to extremely high temperatures and converted into steam to rotate the blades of a turbine, in order to create mechanical or rotational energy.  

This rotational energy caused by the high pressured Steam Turbine is used to generate electricity in an attached generator. Steam turbine Generators require an outside fuel source to heat water into the steam needed for electric production.

QNP`s steam turbine generator can adopt static silicon controlled excitation, two-pole AC brushless excitation and three-pole AC brushless excitation.


Steam Turbine Generator 16


Characteristic and Performance of Generator main parts

Stator:
Stator consists of base, stator core and stator windings.
The base is welded by steel plate, the structure is light and sturdy, and the base is divided into many air inlet and outlet zones in the axial direction;

Stator coil:
It is stacked by strands of copper wire covered by polyester glass fiber, with half-unit type and basket shaped structure (parts of stator coils use transposition structure). The insulation grade of the stator coil is F grade. The stator coil is shaped by continuous wrapping and mould pressing with mica tapes. The coil end is firmly tied up to the support and the bundling ring with unidirectional tapes or dacron-glass ropes thus the turbo-generator unit became highly resistant towards sudden short-circuit conditions. 
   
Stator core:
Stator core is punched and stacked by cold rolled non-oriented, high permeability, low loss high-quality silicon steel sheet, both sides of the silicon steel sheet are coated with a solid insulating film to prevent short-circuit between the stator core pieces to reduce eddy current loss.

Rotor:
The rotor is composed of shaft, coil, center ring, shroud ring and fan ring etc. The rotor coil is made of cold-drawn flat copper wires, and processed by oxygen-free annealing. The rotor coil of generator with 50MW and above is welded together by silver-bearing cold-drawn copper wires and adopts F grade insulation. 

The shroud ring at rotor coil end is made of non-magnetic steel. Both ends of the rotor are equipped with centrifugal fan or axial flow fan with paddle fan blade which is forged by high-strength aluminum alloy.

Rotor machining:
The generator shaft is forged from an integral high-quality alloy steel and has an axial groove formed thereon for fitting a rotor coil and an air groove or a crescent groove is made in the large tooth to enhance the cooling of the main body and the coil end. The slots are processed by special machine for generator rotor processing, Tacchi high precision horizontal slotting and milling machine made in Italy, to ensure the high efficiency of generator. 


Steam Turbine Generator 12

Models

Mainly produce the following models of steam turbine generator and the specifications are as follows:



 No.       Model    
  Capacity  
(KW)
  Frequency  
(Hz) 
  Rated Voltage  
(V)
  Rated Current  
(A)
  Efficiency  
%
Dimension
Weight
(T)
 L 
 (mm) 
W
 (mm) 
H
 (mm) 
 Stator   Rotator   Total 
1 QFD-1.5-2 1500 50/60 400 2706 95.6 3470 1600 1650 4.3 2.3 9.8
450 2406
2 QFD-1.5-2 1500 50/60 3150 344 95.8 3606 1680 1730 4.2 2.56 10.8
3300 328
3 QFD-1.5-2 1500 50/60 6300 171.8 95.8 3606 1680 1730 4.2 2.56 10.9
6600 164
4 QFD-1.5-2 1500 50/60 10500 103.1 95.3 3730 1780 1830 4.72 2.83 11.2
11000 98.4
5 QFD-3-4 3000 50/60 6300 344 96.8 3752 2030 2100 7.2 3.8 17
6600 328
6 QFD-3-4 3000 50/60 10500 206.2 96.4 3752 2030 2100 7.2 3.8 17
11000 196.8
7 QFD-3-2 3000 50/60 6300 344 96.9 3830 1780 1850 6.1 3.51 14.1
6600 328
8 QF-3-2 3000 50/60 6300 344 96.8 3764 1780 1850 6.2 3.51 14.8
6600 328
9 QFD-3-2 3000 50/60 10500 206.2 96.6 3830 1780 1850 6.4 3.51 14.4
11000 196.8
10 QF-3-2 3000 50/60 10500 206.2 96.6 3721 1780 1850 6.4 3.51 14
11000 196.8
11 QFD-4-2 4000 50/60 6300 458.2 96.8 4155 2186 2230 10.4 4.4 20.7
6600 437.4
12 QF-4-2 4000 50/60 6300 458.2 96.8 4040 2186 2230 10.4 4.4 20
6600 437.4
13 QFD-4-2 4000 50/60 10500 275 96.4 4163 1780 1880 8.3 4 16.4
11000 262.4
14 QF-4-2 4000 50/60 10500 275 96.4 4471 1840 1880 8.3 4 16.4
11000 262.4
15 QF-4.5-2 4500 50/60 6300 515.5 96.5 4040 2186 2230 10.4 4.5 19.96
6600 492
16 QF-4.5-2 4500 50/60 10500 309.2 96.5 4040 2186 2230 10.6 4.5 20.1
11000 295
17 QF-6-2 6000 50/60 6300 688 97 4290 2186 2230 11.91 5.24 22.5
6600 656
18 QF-6-2 6000 50/60 10500 412.4 97 4290 2186 2230 12.4 5.15 23.3
11000 393.8
19 QF-7-2 7000 50/60 6300 802 97.1 4290 2186 2230 11.91 5.24 22.5
6600 765.5
20 QF-7-2 7000 50/60 10500 481.1 97.1 4290 2186 2230 12.05 5.24 23.05
11000 450.3
21 QF-7.5-2 7500 50/60 6300 859.2 97.2 4290 2186 2230 11.91 5.24 23
6600 820.1
22 QF-7.5-2 7500 50/60 10500 515.5 97.32 4340 2186 2280 12.8 5.3 24.2
11000 492
23 QF-8-2 8000 50/60 6300 916.5 97.2 4845 2186 2230 14.2 7 29
6600 874.8
24 QF-8-2 8000 50/60 10500 549.9 97 4845 2186 2230 14.2 7 29
11000 524.9
25 QF-9-2 9000 50/60 6300 1031 97.3 4570 2434 2230 16.5 7.2 32
6600 984.2
26 QF-9-2 9000 50/60 10500 618.6 97.2 4590 2434 2230 16.8 7.2 32.4
11000 580.5
27 QF-10-2 10000 50/60 6300 1145.6 97.3 4570 2434 2230 16.5 7.2 32
6600 1093.5
28 QF-10-2 10000 50/60 10500 687.3 97.6 4768 2434 2530 19.24 6.9 32.4
11000 656.1
29 QF-12-2 12000 50/60 6300 1374.7 97.5 5292 2434 2530 21.2 8.8 39.2
6600 1312.2
30 QF-12-2 12000 50/60 10500 825 97.3 5312 2434 2530 24.5 8.9 42
11000 787.4
31 QF-15-2 15000 50/60 6300 1718.4 97.6 5292 2434 2530 21.5 8.8 39.5
6600 1640.3
32 QF-15-2 15000 50/60 10500 1031 97.67 5314 2434 2530 24.5 8.9 42.9
11000 984.2
33 QF-18-2 18000 50/60 6300 2062 97.6 5650 2434 2530 28.5 10 46.8
6600 1968.3
34 QF-18-2 18000 50/60 10500 1237.2 97.47 6030 2730 2815 37.14 14.66 63.1
11000 1181
35 QF-20-2 20000 50/60 6300 2291 97.7 5928 2730 2815 35 12 58
6600 2187
36 QF-20-2 20000 50/60 10500 1374.7 97.5 5928 2730 2815 35.8 12 58.8
11000 1312.2
37 QF-25-2 25000 50/60 6300 2864 97.8 6828 2730 2815 42 16 68
6600 2733.8
38 QF-25-2 25000 50/60 10500 1718.4 97.6 6828 2730 2815 43 16 69
11000 1640
39 QF-30-2 30000 50/60 6300 3437 97.9 6828 2730 2815 42 16 68.7
6600 3280.5
40 QF-30-2 30000 50/60 10500 2062 97.8 6828 2730 2815 43.5 16.2 69.5
11000 1968.3
41 QF-50-2 50000 50/60 6300 5728 98.3 7410 3720 3650 62 19.5 97
6600 5468
42 QF-50-2 50000 50/60 10500 3437 98.3 7745 3720 3650 65 21 105
11000 3280.5
43 QF-60-2 60000 50/60 6300 6873 98.3 7745 3720 3650 67 22 112
6600 6560
44 QF-60-2 60000 50/60 10500 4124 98.3 7745 3720 3650 68 23 115
11000 3937
45 QF-75-2 75000 50/60 10500 5155 98.4 8095 3720 3650 71 25 121
11000 4921
46 QF-100-2 100000 50/60 13800 4922 98.4 9460 4000 3950 122 32 186
47 QF-125-2 125000 50/60 13800 6153 98.4 9790 4000 3950 135 34 198
48 QF-135-2 135000 50/60 13800 6645 94.5 10040 4000 3950 138 37 205
49 QF-155-2 155000 50/60 13800 7629 98.5 10765 4120 4010 140 37.1 210
50 QF-200-2 200000 50/60 15700 9844 98.6 11560 4250 4120 155 43 240



Company Overview:

Located in the Qingzhou city of Shandong province, QNP(QingNeng Power)has developed into the largest leading private manufacturer of Steam Turbines and generators in China, covering an area of 200,000 square meters with building area of 90,000 square meters. We have subsidiaries in Indonesia and Beijing, as well as a branch office in Shanghai. 


about qingneng power-1


QNP has passed such certificates as CE, ISO9000, ISO14001 and OHSAS18001.


Our Product & Service:


QNP`s main products include steam turbines, generators, electrical control equipment,  water treatment equipment and other relevant products.

Manufacturing steam turbine, generator (≤100MW)with I&Cl system, electrical panels & switchgearsspare parts and etc. Providing 1~1000MW Overhaul & Commissioning, Energy Saving Reform and Upgrading, Operation Supervision Service for Power Plant and so on. Contracting Power Plant Turn-key Project.


QNP manufactures various steam turbines. At present, we mainly focus on the research and promotion of single layout and packaged steam turbines, as well as High speed & high efficiency steam turbines.

QingNeng Power Main Products


Manufacturing and Capacities:

With strong manufacturing and machining capacities, main parts and key components of our products are made by CNC machines. More than 400 types of advanced equipment with high accuracy, strong reliability and advanced machining processes are available with QNP, such as the Mitsubishi Planer five sides machining center, the Italy horizontal slotting machine, the 10 meters CNC heavy duty horizontal lathe, the 8 meters vertical lathe, the 6 meters CNC grinding machine, the CNC gantry milling and drilling machine, the CNC gantry wrapping machine and the winding machine for generators. The components are standardized and modularized with enhanced universality and compatibility.


Manufacture & Test


Our state of the art quality test center consists of a physics lab, a chemistry lab, a chemical analysis lab, a precision measurements lab and a metrology lab. The high speed dynamic balancing test machine can test rotors at speeds up to 15000 rpm. The Steam Turbine trial platform can do load tests and performance verification tests. Other instruments such as our German direct-reading spectrometer, tri-linear coordinate measuring instrument, and our speed test platform provide reliable assurance of product quality.


Project Cooperate With Us:

  • QNP, in cooperation with the Chinese Academy of Sciences (CAS) has adapted it's evaporative cooling technology for cooling of distributed energy Generators, which has reduced the size of Generators significantly.
  • In collaboration with Sea Water Desalination Institute of State Oceanic Administration, QNP has formed a technical team to carry out research on the key technologies of power generation and sea water desalination.
  • The rapid development of QNP has captured the attention of the Fortune Global 500 companies, such as the MAN Group from Germany, and Mitsubishi Heavy Industries from Japan. These companies and numerous others have worked with QNP for technical exchanges.
  • QNP has also gotten strong support from central and local government. Top government officials at all levels have visited QNP many times and given high ratings on QNP`s development.

QNP Project


Sales  Network & After Sales:

The market share of QNP is growing steadily and rapidly. Our agents and products have a presence in many countries and regions all over the world such as the U.S.A, Canada, Brazil, Argentina, Russia, Australia, Serbia, India, Indonesia, Pakistan, the Philippines, Thailand, Cambodia, Vietnam, Iran, Myanmar, as well as Sudan, Morocco and Algeria in Africa.


QNP has a skilled and experienced After Sales team geared up for fast response and superior services to our customers at any time. Our Long distance monitoring center is equipped to monitor, diagnose, serve and manage the units delivered. QNP also provides technical training to our customers at regular intervals.


QingNeng Power Company


Product Categories : Generators

Product Images

  • Generac Standby Generator from QNP
Email to this supplier
  • *Subject:
  • *Messages:
    Your message must be between 20-8000 characters